Texas Instruments
Imej mungkin representasi.
Lihat spesifikasi untuk butiran produk.
SN74CBTLVR16292GR
Lihat Butiran Helaian data

SN74CBTLVR16292GR

Product Overview

  • Category: Integrated Circuit (IC)
  • Use: Signal Switching
  • Characteristics: Low Voltage, High-Speed, Bidirectional
  • Package: 56-BGA (Ball Grid Array)
  • Essence: Advanced signal switching solution
  • Packaging/Quantity: Tape and Reel, 2500 units per reel

Specifications

  • Number of Channels: 16
  • Voltage Level: 1.2V to 3.6V
  • Maximum Data Rate: 400 Mbps
  • On-State Resistance: 5 Ohms (typical)
  • Supply Current: 1.5µA (typical)
  • Operating Temperature Range: -40°C to +85°C

Detailed Pin Configuration

The SN74CBTLVR16292GR has a 56-ball BGA package with the following pin configuration:

  1. A1: Channel 1 Input/Output
  2. A2: Channel 2 Input/Output
  3. A3: Channel 3 Input/Output
  4. A4: Channel 4 Input/Output
  5. A5: Channel 5 Input/Output
  6. A6: Channel 6 Input/Output
  7. A7: Channel 7 Input/Output
  8. A8: Channel 8 Input/Output
  9. A9: Channel 9 Input/Output
  10. A10: Channel 10 Input/Output
  11. A11: Channel 11 Input/Output
  12. A12: Channel 12 Input/Output
  13. A13: Channel 13 Input/Output
  14. A14: Channel 14 Input/Output
  15. A15: Channel 15 Input/Output
  16. A16: Channel 16 Input/Output
  17. GND: Ground
  18. OE: Output Enable
  19. VCC: Power Supply

Functional Features

  • Bidirectional signal switching between multiple channels
  • Low voltage operation for compatibility with modern electronic devices
  • High-speed data transmission up to 400 Mbps
  • Minimal power consumption in standby mode
  • ESD (Electrostatic Discharge) protection for enhanced reliability

Advantages and Disadvantages

Advantages: - Wide operating voltage range allows compatibility with various systems - Fast data rate enables efficient signal switching - Low on-state resistance minimizes signal distortion - Small package size saves board space - ESD protection ensures robustness against external disturbances

Disadvantages: - Limited number of channels may not be suitable for applications requiring more inputs/outputs - Relatively high cost compared to simpler signal switches

Working Principles

The SN74CBTLVR16292GR is a bidirectional signal switch that operates by controlling the flow of signals between its input/output channels. It utilizes advanced semiconductor technology to achieve low on-state resistance, high-speed data transmission, and low power consumption. The device can be enabled or disabled using the OE pin, allowing for flexible control of signal routing.

Detailed Application Field Plans

The SN74CBTLVR16292GR is widely used in various applications, including:

  1. Communication Systems: Signal routing and switching in telecommunication equipment.
  2. Data Acquisition: Multiplexing and demultiplexing of analog and digital signals in data acquisition systems.
  3. Test and Measurement: Signal conditioning and switching in test and measurement instruments.
  4. Consumer Electronics: Signal routing in audio/video devices, gaming consoles, and portable electronics.
  5. Industrial Automation: Control signal switching in industrial automation systems.

Detailed and Complete Alternative Models

  1. SN74CBTLV3257: 8-channel bidirectional signal switch with similar characteristics.
  2. SN74CBT16212A: 24-channel bidirectional signal switch with higher channel count.
  3. SN74CBT3257: 8-channel bidirectional signal switch with lower on-state resistance.

These alternative models offer different channel counts and specifications to cater to specific application requirements.

Word Count: 452 words

Senaraikan 10 soalan dan jawapan biasa yang berkaitan dengan aplikasi SN74CBTLVR16292GR dalam penyelesaian teknikal

Sure! Here are 10 common questions and answers related to the application of SN74CBTLVR16292GR in technical solutions:

  1. Q: What is SN74CBTLVR16292GR? A: SN74CBTLVR16292GR is a high-speed, low-power 16-bit bus switch with 3-state outputs. It is commonly used for signal routing and level shifting applications.

  2. Q: What is the operating voltage range of SN74CBTLVR16292GR? A: The operating voltage range of SN74CBTLVR16292GR is typically between 1.65V and 3.6V.

  3. Q: What is the maximum data rate supported by SN74CBTLVR16292GR? A: SN74CBTLVR16292GR supports a maximum data rate of up to 400 Mbps.

  4. Q: Can SN74CBTLVR16292GR be used for bidirectional signal switching? A: Yes, SN74CBTLVR16292GR can be used for bidirectional signal switching as it has 3-state outputs.

  5. Q: How many channels does SN74CBTLVR16292GR have? A: SN74CBTLVR16292GR has 16 channels, allowing it to switch 16 different signals.

  6. Q: What is the typical on-resistance of SN74CBTLVR16292GR? A: The typical on-resistance of SN74CBTLVR16292GR is around 5 ohms.

  7. Q: Can SN74CBTLVR16292GR handle hot-swapping of signals? A: Yes, SN74CBTLVR16292GR is designed to handle hot-swapping of signals without causing any damage.

  8. Q: Is SN74CBTLVR16292GR compatible with different logic families? A: Yes, SN74CBTLVR16292GR is compatible with various logic families such as TTL, CMOS, and LVCMOS.

  9. Q: What is the power supply current consumption of SN74CBTLVR16292GR? A: The power supply current consumption of SN74CBTLVR16292GR is typically very low, making it suitable for low-power applications.

  10. Q: Can SN74CBTLVR16292GR be used in high-speed data communication systems? A: Yes, SN74CBTLVR16292GR is designed to support high-speed data communication systems, making it suitable for applications like PCIe, USB, and SATA.

Please note that these answers are general and may vary depending on specific application requirements. It's always recommended to refer to the datasheet and consult with technical experts for accurate information.